Slag Vertical Roller Mill
Application Industry | Cement Plant, Grinding Station, Steel Mill |
Output | 50~180 t/h |
Blaine Fineness | 4200~4500 cm²/g |
Power Consumption of System | ≤43 kWh/t |
Motor Power | 1600-5000 kW |
GRMK Slag vertical roller mill is also called GGBS vertical roller mill, Slag vertical roller mill is the equipment to grind Ground Granulated Blast furnace Slag (GGBS) into small particles.GGBS (fineness:4200-4500cm2/g) produced by vertical roller mills are being used to substitute clinker in conventional cement manufacturing as well as to partially replace OPC for ready-mixed concrete production, for which the percentage of GGBS usage is typically at 10-15% and 20-25% respectively.
Our GGBS vertical roller mill is typically designed to deal with industrial waste residues generated by the blast-furnace ironmaking. Due to its high physical and chemical activity, and potential hydraulicity, the slag has been widely as admixture matters in the cement industry. And the slag can replace the cement in the concrete to improve the quality and durability of the concrete.
The material through the feed tube fell into the center of grinding plate, and then the materials outwards the surrounding area of grinding plate at centrifugal force, to forms a certain thick layer of materials bed, at the same time material was crushed by number of vertical mill rollers.
The materials continuous moving to the outer edge of the grinding plate, off the grinding plate materials rising with the hot air which enter from wind ring into the vertical roller mill, through the vertical roller mill shell into the middle of the separator, in this course materials and hot gas got a fully heat exchange, the water quickly evaporates.
Separator controls the finished product output size, greater than the specified size are separated and fall back to the plate, while meet the fineness demands are brought through the separator into the finished product warehouse.
1. Good return on investment
The widely use of slag increases the market demand to slag gradually. In recent years, investment in slag production line has been a new favorite in investment market. One production line can recover the cost in 1-3years.
2. Reducing the power consumption of slag micro powder preparation effectively.
According to the display of slag powder production measured data, traditional ball mill needs power consumption 75~80kWh for per ton slag micro powder. However, it needs power consumption 42~45 kWh for per ton slag micro powder if adopts advanced vertical roller mill technology, and it can be saving electricity 33~35kWh use of vertical roller mill production per ton slag, and power saving effect is very remarkable.
3. Reducing the environment pollution effectively in the process of slag powder preparation.
GGBS vertical roller mill adopts the internal negative pressure system to reduce the dust spillover effectively. The equipment adopts advanced technology with low revolving speed, stable operation, low noise, and the noise does not exceed 85dB(A) from the mill 1 meter.
4. Removing iron effectively, increasing additional income.
The advanced technology of slag vertical roller mill can be removed the iron effectively from the slag, and no less than 1% iron content can not only protect the machine, but also can increase additional income.
Investment income
According to association statistics, currently the world each year to produce slag the amount of over 90 million tons, steel slag utilization in 2013 less than 25% , over the past five years the cumulative amount of over 1.279 billion tons discard pile, and the number is increasing, steel companies to environmental management pose serious challenges.
Prodction line gallery:
Model | Grinding Table Diameter (mm) | Roller Diameter (mm) | Roller Number (n) | Motor (kW) | Output (t/h) |
---|---|---|---|---|---|
GRMS26.21 | 2600 | 1600 | 2 | 1000 | 30 |
GRMS33.31 | 3300 | 1700 | 3 | 1600 | 50 |
GRMS35.31 | 3500 | 1800 | 3 | 1800 | 60 |
GRMS40.41 | 4000 | 1900 | 4 | 2240 | 70 |
GRMS43.41 | 4300 | 2120 | 4 | 2800 | 90 |
GRMS46.41 | 4600 | 2240 | 4 | 3150 | 105 |
GRMS48.41 | 4800 | 2240 | 4 | 3550 | 125 |
GRMS50.41 | 5000 | 2360 | 4 | 3800 | 140 |
GRMS53.41 | 5300 | 2500 | 4 | 4200 | 160 |
GRMS56.61 | 5600 | 2500 | 6 | 5000 | 180 |
Note: mill spectral pattern benchmark
(1) Material medium friction (MFs)=0.9~1.0;
(2) Material moisture max 15%;
(3) Refined powder granularity 4200~4500 cm²/g;
(4) Refined powder moisture 0.5~1.0%;
(5) The concrete mill installed power and technology parameter will be adjusted appropritely basing on the actual material property and requirements of owner;
Pre-sales Service:
The wide product range enables us to provide our customers with stand-alone machines or complete processing plants. Based on our customers’ request and budget, our experts make efficient, reliable solutions. Following customers’ order we produce strictly, what’s more, before placing the order every customer has the chance to visit CHAENG working machines or complete plant in the site.
To ease the trip for every visitor to China, in particular the first-time visitor, we provide FOR FREE all relevant visitor-friendly services including invitation letter preparation, hotel reservation, airport pick-up, incity transportation, and sightseeing guide, etc.
After-sales Service:
Experienced technicians guidance is available on the phone, and on the internet. One or more engineers will be dispatched to the quarry site to help install the customers’ plants. Necessary training about machine daily maintenance to local workers is provided also.
After-Sales department is made of well-trained employees and installation engineers, the installation engineers are special and professional members of CHAENG, they are now strategically located home and abroad, working for our customers.
Applied material:
Blast-Furnace Slag, building material, limestone,slag,rock, talc, etc.